Industry Information

Knife sticking problem when machining aluminum parts by CNC machining center

Knife sticking problem when machining aluminum parts by CNC machining center

Will the CNC machining center handle aluminum parts attached to the knife?
Answer: This has nothing to do with the machining center. Choose the right tool. General tools can choose 3 blades. If the tungsten steel blade should specify the aluminum blade, of course, the cutting amount and the advance speed are also related~
When the machining center processes aluminum parts, the tools and corresponding parameters are adjusted to more…
Question: When machining aluminum parts with a machining center, when are the main tools for roughing and the corresponding spindle speed…
Answer: When the aluminum alloy material is worn, use a common knife F1800 S7500ž5MM 150-300 for the radiator cavity. Rough skin knife alloy F2500 S7800 I made a Z aluminum 5-10mm product for 4 years, if it has a high-speed machine can catch up, do nothing. This is not to manufacture products or slow down. Don’t listen to them climbing upstairs…
What type of blade is used for CNC milling machine to process pure aluminum?
Answer: CNC milling machines that use high-speed double-blade steel blades to process pure aluminum will not stick to the blades. When processing, the shaft does not need such a high speed, 2000 revolutions is enough, aluminum is relatively smooth; if the number is not large, the power can be 200-250MM/MIN; eating 5MM is irrelevant, only the input is 30-50MM /MIN. CNC milling machine is developed on the basis of ordinary milling machine…
Q: What about tools for cutting aluminum?
Answer: When grinding, adding more emulsion is very effective to prevent the influence of aluminum scraping. Of course, if you can add kerosene, the effect will be better.
Q: How to prevent the aluminum knife from sticking.
Answer: The blade is sharper and more lubricated. The aluminum scraps are deformed, rubbed and sticky.
Can the machining center process aluminum alloys?
Answer: From the viewpoint of industrial materials, aluminum alloy also has certain mechanical properties, low density, good electrical conductivity and thermal conductivity, so it is widely used in the industrial field, one of the same type of processing center processing. Aluminum alloy has low strength and toughness, good cutting load, due to good thermal conductivity and heat dissipation is fast, and the melting point of aluminum alloy is relatively low…
CNC machining center processing aluminum alloy
Question: How to process 10, 20, 50 diameter aluminum alloy, balance xy, balance 5-10mmz balance 20-50mm…
Answer: The material of aluminum alloy itself is very soft, the spindle speed must be high (the tool can withstand it), and the feeding speed must be small. If the feeding amount is large, the chip removal will be difficult, as long as it processes aluminum. It is not difficult to find that there is always aluminum adhesion in the tool. This means that the cutting fluid used is incorrect. For processing aluminum, diesel fuel must be used as the cutting fluid. The tool must be very sharp. It is best to use two or…
Is it possible to mill aluminum inserts for machining centers?
Answer: Pay attention to use: Ordinary fruit knives or kitchen knives are usually made of steel or stainless steel, iron knives are mostly hard, aluminum knives are too soft to use, but there are also several scalpels that will use aluminum separately. Why can’t CNC machining center use aluminum alloy cutter to cut aluminum parts, but…
Answer: Carbide drills can actually mill aluminum parts, but why does it have professional lightweight aluminum blades or flat blades? At present, there are roughly three types of tool materials for processing aluminum alloys, high-speed steel and cemented carbide, Diamond PCD. In fact, it can be said that carbide cutting tools are the most commonly used; high-quality fine materials and sharp milling cutters; why CNC machining centers cannot use aluminum alloy cutting tools to cut aluminum parts.
Q: Can steel knives process steel?
Answer: The above question is actually a false proposition. Carbide drills can actually mill aluminum parts, but why does it have a light aluminum knife or a flat knife? This is mainly because you are not familiar with the tool; the materials currently used for machining aluminum alloy processing are about three kinds of high-speed steel, cemented carbide, and PCD diamond.

Leave a Reply